The unified diff between revisions [7f3278b1..] and [dc88787e..] is displayed below. It can also be downloaded as a raw diff.

This diff has been restricted to the following files: 'stick.c'

#
# old_revision [7f3278b164104bb0564a391a1f7b4fd955a3904a]
# new_revision [dc88787ecd1d574feba045763baed2a7651ff33d]
#
# patch "stick.c"
#  from [ad24bc7d9d8c95c497a1b5bd7a13d8e1619ca539]
#    to [2f04655a185f179c9e8469822e089c308cb3a220]
#
============================================================
--- stick.c	ad24bc7d9d8c95c497a1b5bd7a13d8e1619ca539
+++ stick.c	2f04655a185f179c9e8469822e089c308cb3a220
@@ -12,38 +12,46 @@
 #include "timer.h"
 #include "trig.h"
 #include "motor.h"
-#include "wmp.h"
 #include "status.h"
 #include "watchdog.h"
+#include "log.h"
+#include "config.h"
 
 #define TWO_PI 6.28318531f
 #define PI 3.14159265f
 
-#define MIN_X 15830
-#define MAX_X 28300
-#define CENTRE_X 22100
+#define MIN_X config.stick.timing.x.min
+#define MAX_X config.stick.timing.x.max
+#define CENTRE_X config.stick.timing.x.centre
 
-#define MIN_Y 18530
-#define MAX_Y 28200
-#define CENTRE_Y 22100
+#define MIN_Y config.stick.timing.y.min
+#define MAX_Y config.stick.timing.y.max
+#define CENTRE_Y config.stick.timing.y.centre
 
-#define MIN_Z 15800
-#define MAX_Z 28304
-#define CENTRE_Z 22100
+#define MIN_Z config.stick.timing.z.min
+#define MAX_Z config.stick.timing.z.max
+#define CENTRE_Z config.stick.timing.z.centre
 
-#define MIN_THR 16500
-#define MAX_THR 28275
+#define MIN_THR config.stick.timing.throttle.min
+#define MAX_THR config.stick.timing.throttle.max
 
-#define MIN_REAL_THR 15830
+#define MIN_REAL_THR 8720
 
 #define CENTRE_ZONE 100
 
+/* With new TX firmware, CPPM:
+ *             x      y    thr      z
+ * centre: 16260, 16258, 16000, 16300
+ * min:     8720,  8718, 8720,  8722 
+ * max:    23790, 23817, 23750, 23803
+ */
+
 /* Full scale is a roll/pitch angle of 30 degrees from the vertical */
-#define SCALE_X (TWO_PI*30.0/360.0 / (MAX_X-CENTRE_X))
-#define SCALE_Y (TWO_PI*30.0/360.0 / (MAX_Y-CENTRE_Y))
+#define SCALE_X (TWO_PI*config.stick.sensitivity.x/360.0 / (MAX_X-CENTRE_X))
+#define SCALE_Y (TWO_PI*config.stick.sensitivity.y/360.0 / (MAX_Y-CENTRE_Y))
 
 /* Full scale is a complete rotation in one second */
-#define SCALE_Z (TWO_PI / (MAX_Z-CENTRE_Z))
+#define SCALE_Z (TWO_PI*config.stick.sensitivity.z/360.0 / (MAX_Z-CENTRE_Z))
 
 /* 0 is min throttle, 1 is max throttle */
 #define SCALE_THROTTLE (1.0f/(MAX_THR - MIN_THR))
@@ -52,9 +60,9 @@ unsigned int stick_counter;
 
 unsigned int stick_counter;
 
-void stick_update(float x, float y, float z)
+void stick_update(vec3f stick)
 {
-	float tz = delta_t * z;
+	float tz = delta_t * stick.z;
 
 	stick_yaw += tz;
 
@@ -65,26 +73,62 @@ void stick_update(float x, float y, floa
 	    stick_yaw -= TWO_PI;
 
 #if 0
-	z = stick_yaw;
+	stick.z = stick_yaw;
 #endif
 
-	x = sine(x);
-	y = sine(y);
+	stick.x = sine(stick.x);
+	stick.y = sine(stick.y);
 #if 0
-	z = 1.0/fisqrt(1-x*x-y*y);
+	stick.z = 1.0/fisqrt(1-stick.x*stick.x-stick.y*stick.y);
 #endif
 
-	dcm_attitude_error(x, y, z);
+	dcm_attitude_error(stick);
 }
 
+#ifdef STICK_DEBUG_CALIBRATE
+void stick_debug_calibrate()
+{
+	unsigned int t1 = timer_input(0);
+	unsigned int t2 = timer_input(1);
+	unsigned int t3 = timer_input(2);
+	unsigned int t4 = timer_input(3);
+        putstr("S:(");
+        putint(t1);
+        putstr(",");
+        putint(t2);
+        putstr(",");
+        putint(t3);
+        putstr(",");
+        putint(t4);
+        putstr(")\r\n");
+}
+#endif
+
 void stick_input(void) {
 	float x, y, z, throttle;
+	unsigned int xi, yi, zi, throttlei;
+
 	if (timer_allvalid()) {
-		x = timer_input(0);
-		y = timer_input(1);
-		throttle = timer_input(2);
-		z = timer_input(3);
+		xi = timer_input(0);
+		yi = timer_input(1);
+		throttlei = timer_input(2);
+		zi = timer_input(3);
 
+		log_put_uint16(xi);
+		log_put_uint16(yi);
+		log_put_uint16(throttlei);
+		log_put_uint16(zi);
+
+		x = xi;
+		y = yi;
+		throttle = throttlei;
+		z = zi;
+
+#ifdef STICK_DEBUG_CALIBRATE
+		if ((stick_counter % 100) == 0)
+			stick_debug_calibrate();
+#endif
+
 		if (!status_armed()) {
 			if ((throttle < MIN_THR) &&
 			    (x > (CENTRE_X - CENTRE_ZONE)) &&
@@ -109,6 +153,10 @@ void stick_input(void) {
 		if (throttle < 0.0)
 			throttle = 0.0;
 	} else {
+		log_put_uint16(0);
+		log_put_uint16(0);
+		log_put_uint16(0);
+		log_put_uint16(0);
 		x = 0.0f;
 		y = 0.0f;
 		z = 0.0f;
@@ -121,9 +169,7 @@ void stick_input(void) {
 	watchdog_kick(WATCHDOG_STICK);
 
 	/* So the controls are back to front. Let's fix that. */
-	x = -x;
-	y = -y;
-	z = -z;
+	vec3f stick = {-x, -y, -z};
 
 #if 0
 	if ((stick_counter % 100) == 0) {
@@ -134,10 +180,10 @@ void stick_input(void) {
 #endif
 
 #if 1
-	stick_update(x, y, z);
+	stick_update(stick);
 #else
 	if ((stick_counter % 100) == 0)
-		stick_update(x, y, z);
+		stick_update(stick);
 #endif
 
 /*