import serial from sys import version_info PY2 = version_info[0] == 2 #Running Python 2.x? # #--------------------------- # Maestro Servo Controller #--------------------------- # # Support for the Pololu Maestro line of servo controllers # # Steven Jacobs -- Aug 2013 # https://github.com/FRC4564/Maestro/ # # These functions provide access to many of the Maestro's capabilities using the # Pololu serial protocol # class Controller: # When connected via USB, the Maestro creates two virtual serial ports # /dev/ttyACM0 for commands and /dev/ttyACM1 for communications. # Be sure the Maestro is configured for "USB Dual Port" serial mode. # "USB Chained Mode" may work as well, but hasn't been tested. # # Pololu protocol allows for multiple Maestros to be connected to a single # serial port. Each connected device is then indexed by number. # This device number defaults to 0x0C (or 12 in decimal), which this module # assumes. If two or more controllers are connected to different serial # ports, or you are using a Windows OS, you can provide the tty port. For # example, '/dev/ttyACM2' or for Windows, something like 'COM3'. def __init__(self,ttyStr='/dev/ttyACM0',device=0x0c,baud=115200): # Open the command port self.usb = serial.Serial(ttyStr,baudrate=baud) # Command lead-in and device number are sent for each Pololu serial command. self.PololuCmd = chr(0xaa) + chr(device) # Track target position for each servo. The function isMoving() will # use the Target vs Current servo position to determine if movement is # occuring. Upto 24 servos on a Maestro, (0-23). Targets start at 0. self.Targets = [0] * 24 # Servo minimum and maximum targets can be restricted to protect components. self.Mins = [0] * 24 self.Maxs = [0] * 24 # Cleanup by closing USB serial port def close(self): self.usb.close() # Send a Pololu command out the serial port def sendCmd(self, cmd): cmdStr = self.PololuCmd + cmd if PY2: self.usb.write(cmdStr) else: self.usb.write(bytes(cmdStr,'latin-1')) # Set channels min and max value range. Use this as a safety to protect # from accidentally moving outside known safe parameters. A setting of 0 # allows unrestricted movement. # # ***Note that the Maestro itself is configured to limit the range of servo travel # which has precedence over these values. Use the Maestro Control Center to configure # ranges that are saved to the controller. Use setRange for software controllable ranges. def setRange(self, chan, min, max): self.Mins[chan] = min self.Maxs[chan] = max # Return Minimum channel range value def getMin(self, chan): return self.Mins[chan] # Return Maximum channel range value def getMax(self, chan): return self.Maxs[chan] # Set channel to a specified target value. Servo will begin moving based # on Speed and Acceleration parameters previously set. # Target values will be constrained within Min and Max range, if set. # For servos, target represents the pulse width in of quarter-microseconds # Servo center is at 1500 microseconds, or 6000 quarter-microseconds # Typcially valid servo range is 3000 to 9000 quarter-microseconds # If channel is configured for digital output, values < 6000 = Low ouput def setTarget(self, chan, target): # if Min is defined and Target is below, force to Min if self.Mins[chan] > 0 and target < self.Mins[chan]: target = self.Mins[chan] # if Max is defined and Target is above, force to Max if self.Maxs[chan] > 0 and target > self.Maxs[chan]: target = self.Maxs[chan] # lsb = target & 0x7f #7 bits for least significant byte msb = (target >> 7) & 0x7f #shift 7 and take next 7 bits for msb cmd = chr(0x04) + chr(chan) + chr(lsb) + chr(msb) self.sendCmd(cmd) # Record Target value self.Targets[chan] = target # Set speed of channel # Speed is measured as 0.25microseconds/10milliseconds # For the standard 1ms pulse width change to move a servo between extremes, a speed # of 1 will take 1 minute, and a speed of 60 would take 1 second. # Speed of 0 is unrestricted. def setSpeed(self, chan, speed): lsb = speed & 0x7f #7 bits for least significant byte msb = (speed >> 7) & 0x7f #shift 7 and take next 7 bits for msb cmd = chr(0x07) + chr(chan) + chr(lsb) + chr(msb) self.sendCmd(cmd) # Set acceleration of channel # This provide soft starts and finishes when servo moves to target position. # Valid values are from 0 to 255. 0=unrestricted, 1 is slowest start. # A value of 1 will take the servo about 3s to move between 1ms to 2ms range. def setAccel(self, chan, accel): lsb = accel & 0x7f #7 bits for least significant byte msb = (accel >> 7) & 0x7f #shift 7 and take next 7 bits for msb cmd = chr(0x09) + chr(chan) + chr(lsb) + chr(msb) self.sendCmd(cmd) # Get the current position of the device on the specified channel # The result is returned in a measure of quarter-microseconds, which mirrors # the Target parameter of setTarget. # This is not reading the true servo position, but the last target position sent # to the servo. If the Speed is set to below the top speed of the servo, then # the position result will align well with the acutal servo position, assuming # it is not stalled or slowed. def getPosition(self, chan): cmd = chr(0x10) + chr(chan) self.sendCmd(cmd) lsb = ord(self.usb.read()) msb = ord(self.usb.read()) return (msb << 8) + lsb # Test to see if a servo has reached the set target position. This only provides # useful results if the Speed parameter is set slower than the maximum speed of # the servo. Servo range must be defined first using setRange. See setRange comment. # # ***Note if target position goes outside of Maestro's allowable range for the # channel, then the target can never be reached, so it will appear to always be # moving to the target. def isMoving(self, chan): if self.Targets[chan] > 0: if self.getPosition(chan) != self.Targets[chan]: return True return False # Have all servo outputs reached their targets? This is useful only if Speed and/or # Acceleration have been set on one or more of the channels. Returns True or False. # Not available with Micro Maestro. def getMovingState(self): cmd = chr(0x13) self.sendCmd(cmd) if self.usb.read() == chr(0): return False else: return True # Run a Maestro Script subroutine in the currently active script. Scripts can # have multiple subroutines, which get numbered sequentially from 0 on up. Code your # Maestro subroutine to either infinitely loop, or just end (return is not valid). def runScriptSub(self, subNumber): cmd = chr(0x27) + chr(subNumber) # can pass a param with command 0x28 # cmd = chr(0x28) + chr(subNumber) + chr(lsb) + chr(msb) self.sendCmd(cmd) # Stop the current Maestro Script def stopScript(self): cmd = chr(0x24) self.sendCmd(cmd)