The unified diff between revisions [7f3278b1..] and [9142f333..] is displayed below. It can also be downloaded as a raw diff.
This diff has been restricted to the following files: 'stick.c'
# # old_revision [7f3278b164104bb0564a391a1f7b4fd955a3904a] # new_revision [9142f3330490a5aa00c1686475633b620c2ef5e7] # # patch "stick.c" # from [ad24bc7d9d8c95c497a1b5bd7a13d8e1619ca539] # to [50fffafb58abb3d5935c27843ff50c4bd4ec5300] # ============================================================ --- stick.c ad24bc7d9d8c95c497a1b5bd7a13d8e1619ca539 +++ stick.c 50fffafb58abb3d5935c27843ff50c4bd4ec5300 @@ -12,32 +12,39 @@ #include "timer.h" #include "trig.h" #include "motor.h" -#include "wmp.h" #include "status.h" #include "watchdog.h" +#include "log.h" #define TWO_PI 6.28318531f #define PI 3.14159265f -#define MIN_X 15830 -#define MAX_X 28300 -#define CENTRE_X 22100 +#define MIN_X 8720 +#define MAX_X 23800 +#define CENTRE_X 16260 -#define MIN_Y 18530 -#define MAX_Y 28200 -#define CENTRE_Y 22100 +#define MIN_Y 8720 +#define MAX_Y 23800 +#define CENTRE_Y 16260 -#define MIN_Z 15800 -#define MAX_Z 28304 -#define CENTRE_Z 22100 +#define MIN_Z 8720 +#define MAX_Z 23800 +#define CENTRE_Z 16300 -#define MIN_THR 16500 -#define MAX_THR 28275 +#define MIN_THR 9720 +#define MAX_THR 23750 -#define MIN_REAL_THR 15830 +#define MIN_REAL_THR 8720 #define CENTRE_ZONE 100 +/* With new TX firmware, CPPM: + * x y thr z + * centre: 16260, 16258, 16000, 16300 + * min: 8720, 8718, 8720, 8722 + * max: 23790, 23817, 23750, 23803 + */ + /* Full scale is a roll/pitch angle of 30 degrees from the vertical */ #define SCALE_X (TWO_PI*30.0/360.0 / (MAX_X-CENTRE_X)) #define SCALE_Y (TWO_PI*30.0/360.0 / (MAX_Y-CENTRE_Y)) @@ -77,14 +84,50 @@ void stick_update(float x, float y, floa dcm_attitude_error(x, y, z); } +#ifdef STICK_DEBUG_CALIBRATE +void stick_debug_calibrate() +{ + unsigned int t1 = timer_input(0); + unsigned int t2 = timer_input(1); + unsigned int t3 = timer_input(2); + unsigned int t4 = timer_input(3); + putstr("S:("); + putint(t1); + putstr(","); + putint(t2); + putstr(","); + putint(t3); + putstr(","); + putint(t4); + putstr(")\r\n"); +} +#endif + void stick_input(void) { float x, y, z, throttle; + unsigned int xi, yi, zi, throttlei; + if (timer_allvalid()) { - x = timer_input(0); - y = timer_input(1); - throttle = timer_input(2); - z = timer_input(3); + xi = timer_input(0); + yi = timer_input(1); + throttlei = timer_input(2); + zi = timer_input(3); + log_put_uint16(xi); + log_put_uint16(yi); + log_put_uint16(throttlei); + log_put_uint16(zi); + + x = xi; + y = yi; + throttle = throttlei; + z = zi; + +#ifdef STICK_DEBUG_CALIBRATE + if ((stick_counter % 100) == 0) + stick_debug_calibrate(); +#endif + if (!status_armed()) { if ((throttle < MIN_THR) && (x > (CENTRE_X - CENTRE_ZONE)) &&